Knowledge Test Class A #2
Class A Driving Test | Utah 2024 #2 Page 5 of 7
Train for FREE online with our Utah class A license test. The official exam test consists of several obligatory parts, with all of them checking your knowledge of different blocks of road rules. If you need to obtain a UT CDL class A permit in 2024, practice as much as possible. Free sample tests published on our website will help you check and improve your knowledge and boost your grades. Please bear in mind that CDL class A requirements may vary from state to state.
50
40
20
29 . How can you prevent drowsiness before a trip?
Schedule long trips at night.
To prevent drowsiness on a long trip, strategies include getting adequate sleep beforehand; planning out the route and stopping points in advance; driving with a passenger; and driving at times during which you are normally awake.
30 . What can happen if one-fourth of the leaves in a leaf spring are missing when a vehicle is inspected?
The driver will be asked to decrease the weight of the load.
If at least one-fourth of the leaves in a leaf spring are missing, the vehicle will be put out-of-service until the defect is fixed.
31 . At what psi is the safety valve set to open?
500 psi
In an air brake system, the first tank that receives compressed air has a safety valve that releases air if the pressure gets too high. It is usually set to open at 150 psi. If the valve must open, there is a fault in the system that should be repaired by a mechanic.
32 . If an air compressor is belt-driven, the belt should be routinely checked to ensure that it is:
If your vehicle has air brakes, the air compressor drive belt should be checked before each drive. Check the tightness of the belt and verify that it is in good condition.
33 . Drivers may use ____ red reflective warning triangles when their vehicle is stopped on the side of the road.
Seven
If a vehicle carries red reflective triangles, the driver should place three of them as warning devices when the vehicle is parked on the road.
34 . The tire load:
Tire load is the maximum weight a tire can safely carry at a given pressure. This rating is stated on the side of each tire.
35 . A light usually illuminates when gears should be shifted.
There are two indicators that determine when you need to shift into a higher gear. One indicator is the engine speed (rpm). You should read your vehicle's manual to learn its rpm range and shift up when you reach the top of that range. The other indicator is road speed (mph). You should learn which speeds each gear can accommodate, then keep an eye on the speedometer and shift up as needed.
2024 Utah | Frequently Asked Questions
To acquire a CDL Tank endorsement in Utah, you must first have a valid CDL. Then, you need to pass the Tank Vehicle written test at a Utah Driver License Division office. The test covers knowledge about tank vehicles, their unique properties, and how to safely operate them. Once you pass the test, the endorsement will be added to your CDL.
To obtain a CDL Tank license, you need a valid Commercial Driver's License (CDL). You must then pass the Tank Vehicle written test, which covers knowledge on the safe operation and unique properties of tank vehicles. The test is offered at Utah Driver License Division offices. Once passed, the endorsement is added to your CDL.
While specific training is not mandatory for a CDL Tank endorsement in Utah, it's highly recommended to prepare for the endorsement test. You should understand the safety protocols, inspection procedures, and driving techniques for tank vehicles. Practical experience, although not required, can also be beneficial. Always refer to Utah's CDL manual for comprehensive information.
Yes, to obtain a CDL Tank endorsement in Utah, you are required to pass an additional written test. This test focuses on the safe operation and unique properties of tank vehicles. It is separate from the general CDL test and must be taken at a Utah Driver License Division office.
The written test for a CDL Tank endorsement covers various subjects related to tank vehicles. This includes the inspection and maintenance of tank vehicles, understanding bulk packaging markings, driving stability and handling, safe driving rules, and emergency response procedures. The test is designed to ensure drivers can safely operate tank vehicles.
During the CDL Tank endorsement assessment in Utah, several skills and maneuvers are assessed. These include inspecting the tank vehicle for safety, proper loading and unloading procedures, controlling the vehicle's speed and braking, maneuvering through turns and curves, and maintaining control during emergency situations. Additionally, knowledge of hazardous materials regulations and proper handling procedures is also evaluated.
Yes, drivers with a CDL Tank endorsement must adhere to specific regulations. They must ensure the load is properly balanced and secure, follow all safety procedures when loading and unloading, and handle hazardous materials carefully. Additionally, they must comply with hours-of-service regulations to prevent driver fatigue. Violation of these rules can result in fines, suspension, or revocation of the endorsement.
No, a valid CDL Tank endorsement is required to transport liquid or gas materials. This ensures the driver is knowledgeable and skilled in handling such materials, which can pose unique challenges and risks. Driving without the necessary endorsement is illegal and can result in serious penalties, including fines and suspension of the driver's CDL.
Yes, a CDL Tank endorsement can be added to your current commercial driver's license. You don't need to apply for a new license. However, you will need to pass the tank vehicle written test and pay the required fee. The endorsement allows you to transport liquid or gas materials in a tank vehicle. Always ensure you comply with all regulations.
Yes, to handle hazardous materials in Utah, you must have both a CDL Tank endorsement and a Hazardous Materials (HazMat) endorsement. Getting the HazMat endorsement involves passing a knowledge test, undergoing a TSA background check, and fingerprinting. This ensures that drivers are trained to handle these materials safely and understand the associated risks and precautions.