Tank #2
Tank Endorsement Test | Utah 2024 #2 Page 2 of 3
Train for FREE with our Utah tank endorsement practice test online. The official exam test consists of several obligatory parts, with all of them checking your knowledge of different blocks of road rules. If you need to obtain a UT tank license in 2024, practice as much as possible. Free sample tests published on our website will help you check and improve your knowledge and boost your grades. Please bear in mind that DMV requirements for issuing a CDL tank vehicle endorsement may vary from state to state.
20
16
20
8 . Tread depth in the major grooves on a front tire should be at least:
3/4 of an inch.
Tires need to have at least 4/32 of an inch of tread depth in every major groove on the front tires, and at least 2/32 of an inch of tread depth on other tires.
9 . When stopping a manual transmission vehicle, what should you do when the engine is close to idle?
Shut off the vehicle.
When stopping a vehicle with a manual transmission, you should push in the clutch when the engine is close to idle.
10 . Rough acceleration:
Should be used to prevent rust from forming.
Always accelerate smoothly and gradually so that your vehicle does not jerk. Rough acceleration can cause mechanical damage.
11 . A front tire with a tread depth of 1/32 an inch is acceptable.
Tires need to have at least 4/32 of an inch of tread depth in every major groove on the front tires, and at least 2/32 of an inch of tread depth on other tires.
12 . At least eight red reflective triangles must be carried within a commercial motor vehicle.
All commercial motor vehicles are required to be equipped with the proper emergency equipment. This may include spare electrical fuses; three red reflective triangles, six fuses, or three liquid burning flares; and at least one properly charged and rated fire extinguisher.
13 . Tires with deep cracks are usually acceptable.
When inspecting a vehicle's tires, you should make sure that there is no damage present on the tires.
14 . Dual tires should be in contact with each other.
When inspecting a vehicle's tires, you should ensure that dual tires do not come into contact with each other or with other parts of the vehicle.
2024 Utah | Frequently Asked Questions
A CDL Class A license in Utah is defined as a commercial driver's license that allows the holder to operate any combination of vehicles with a gross combination weight rating (GCWR) of 26,001 pounds or more, provided the towed vehicle(s) weigh more than 10,000 pounds. It includes vehicles like tractor-trailers, truck and trailer combinations, and flatbeds.
A Class A CDL license allows you to operate a variety of large vehicles such as tractor-trailers, truck and trailer combinations, tank vehicles, livestock carriers, and flatbeds. This license is also required for operating vehicles that tow trailers or other vehicles with a GVWR of over 10,000 pounds.
To obtain a Class A CDL license in Utah, you must be at least 18 years old for intrastate driving, or 21 for interstate. You need a valid Utah driver’s license, pass a vision exam, and obtain a medical certificate. You must also pass written knowledge tests and a three-part skills test, which includes a pre-trip vehicle inspection, a basic controls test, and a driving test.
In Utah, you must be at least 18 years old to qualify for a Class A Commercial Driver's License (CDL) for intrastate (within the state) driving. However, to drive interstate (across state lines), transport hazardous materials, or drive a school bus, you must be at least 21 years old.
Specific endorsements are not required for a Class A CDL license, but they can provide additional driving privileges. Endorsements include: H (Hazardous Materials), N (Tank Vehicles), P (Passenger Transport), S (School Buses), T (Double/Triple Trailers), and X (Combination of Tank Vehicle and Hazardous Materials). Each endorsement requires passing a specific knowledge test.
The Class A CDL skills test in Utah includes three parts: a pre-trip vehicle inspection, a basic controls test, and a driving test. The pre-trip inspection assesses your ability to inspect your vehicle before driving. The basic controls test evaluates your ability to maneuver and control the vehicle. The driving test evaluates your on-road driving skills.
Yes, limitations can be imposed on Class A CDL license holders in Utah. These restrictions are based on the driver's abilities and the type of vehicle they tested in. For instance, if a driver takes the skills test in a vehicle without air brakes, they will have an "L" restriction, indicating they are not authorized to operate vehicles with air brakes.
In Utah, the written Class A CDL test is primarily offered in English. However, some locations may offer the test in Spanish as well. It's important to note that federal regulations require all commercial drivers to read and speak English sufficiently to converse with the general public, understand highway signs and signals, respond to official inquiries, and make entries on reports and records.
Yes, accommodations can be provided for the Class A CDL written test for individuals with disabilities in Utah. The state complies with the Americans with Disabilities Act (ADA). You'll need to provide documentation of your disability and specify your required accommodation when scheduling your test. It's recommended to contact the Utah Driver License Division for detailed procedures.
Yes, you can retake the Class A CDL written test in Utah if you don't pass it the first time. However, you must wait until the next day to retake it. There's also a retest fee that you'll have to pay each time you retake the test. It's advisable to study thoroughly before reattempting to increase your chances of passing.